Morphagene advice

karst · 2018-03-28T03:38:52.983Z

Just as a heads-up @Virtual_Flannel, the Intellijel 1u modules are not compatible with the pulplogic cases 1u rows without some modification (I think you’d have to grind down or otherwise reduce the panel height).

Virtual_Flannel · 2018-03-28T03:58:48.869Z

Did some research I think the intellijel 1u are smaller so you can only screw in one side and there is an ugly gap, but it still works. Was thinking they should make little fillers that you could put in the space over top.

D26CEEAE-3DBA-41AA-AF32-4C4446DBE9F4.jpeg4000×2992 857 KB

polyoptics · 2018-03-28T04:08:25.892Z

Look who it is! Welcome @Virtual_Flannel ! I knew it was only a matter of time.
I’m looking forward to see your adventures in modular.

Virtual_Flannel · 2018-03-28T15:18:37.281Z

Thanks for the warm welcome homie!

DuellingAnts · 2019-12-31T12:24:12.210Z

Thinking of making my way into modular with a small case based around the Morphagene, so bumping this thread for some advice

My idea is to mainly use it for live manipulation together with op-1/organelle. I’ll probably record stuff to it and use it on it’s own as well though so I want to pair it with a module that would give me a lot of interesting options for modulation.

Keeping it simple to start off. Would Pamelas New Workout be a good companion? Or perhaps the Wogglebug is better?

Also, would i need som kind of module like 4ms listen io to get the levels right?

Kheone · 2019-12-31T14:27:12.549Z

pam’s is good if you don’t mind some relatively straightforward menu diving.
I enjoy Batumi a lot with it.

Morphagene has auto leveling, though it is a little tricky. You’d need some sort of mic amp though if you wanted a microphone hooked up, and then something to get the sound out of the whole system. I use 4MS Listen. It’s good. I really enjoy the morphagene, for what it is worth.

Quru · 2020-01-01T13:53:51.497Z

I have Morphagene and ResEQ too, what a wonderful combo. Slight warble modulation on the speed and “tuning” the sound with the eq bands sounds so lovely. It can really make the sounds sing.

kasselvania · 2020-05-22T23:22:14.243Z

I have a question for Morphagene users; it appears as if I cannot record in to a new splice. I have something playing, hold down record and press splice. I then do all my junk. Then I press record again, to stop recording. The shift light blinks, but I have no new splices on my reel. The splice window stays that original blue all the way through. Am I missing something?

Edit: Found my issue; bought it used, options.txt were not factory settings.

Justmat · 2020-05-23T12:50:02.954Z

That’s the only special setting i use! just press record to record into a new splice

kasselvania · 2020-05-23T13:20:34.939Z

I could see the being useful. That way, you’re always preserving the original, even if you’re just overdubbing with a new record… everything goes in a new splice… plus, 3 min is a long time! Even if you’re going for the TLA

I think I might go back to that setting, now that I realized what was actually happening. Haha.

Dogma · 2020-08-14T07:54:40.167Z

hey liners - I was hoping someone may be able to help me out here - I just got a morphagene and im trying to update to the latest firmware but I noticed the SD card that came with it has a nearly empty options.txt file - just one line

1 32768 0

ive searched far and wide and I have no idea how to populate it (the FW update is .wav file and doesn’t require the sd card.)

Super confused

kveye · 2020-08-14T08:11:23.271Z

Do the update procedure and then Morphagene will populate the file with parameters.

kasselvania · 2020-08-14T15:11:11.127Z

You apply the update by playing that audio file through a patch cable, not placing it on the SD card.

Follow these steps:

Dogma · 2020-08-14T23:47:53.117Z

Thank you both - I knew I had to play the .wav file into morphagene, ive updated a few modules over the years it just wasn’t clear that the morphagene populated that file AFTER the FW update, but after the update and a power down and up and again, it populated
Its like a new new module for Me. Massive update

sqrlfrtz · 2020-09-02T21:15:44.481Z

I just ran into a really weird issue with Morphagene today. I recorded something into Morphagene a couple days ago hoping to come back to it today, but it was gone. However something I recorded a week ago that I deleted was in its place. I looked through reel mode just in case to see if it was there, but nothing.

This is so bizarre. Has this happened to anyone else?

jhyde · 2021-05-29T06:37:17.840Z

Hiya, I have hundreds of prepared samples that are all different bit and sample rates, could I batch convert them to 48 & 32 bit rate to load into the Morphagene without any problems? I understand they need to be in this format to be read. Wondering what the device does if the samples aren’t actually at those rates but formatted to be. thanks!

swim_tortuga · 2021-05-29T07:08:26.985Z

https://www.lorenzostanco.com/lab/morphagene/

That is ace. Should help you along…

avantworld · 2022-08-16T20:44:34.227Z

Had anyone used an SD card reader and an iPad for reel/splice management?

If so, what app should I use?

Thanks!

dspk · 2022-08-17T04:57:59.605Z

You can just use the built in file browser in iOS (though I’m not sure which version this was introduced with , iOS 13 maybe?).

I use it for firmware updates on sd card based devices too

If you also want to edit the config file there are a few editor apps- I’ve been using koder

avantworld · 2022-08-17T19:11:50.238Z

thanks!

what app do you recommend to chop up samples and/or add markers?