#691

Thanks… bummer. Time to borrow somebody’s newer MacBook, whenever 2.0 image is made available. Any volunteers? Haha

edit: What could be the harm in giving it a shot on 10.12? @ngwese

#692

I don’t think there is any harm in trying it w/ 10.12. If I had to guess the most critical piece may just be building the latest version of rpiboot.

1 Like
#693

Not sure if it’s my pathing issues or otherwise, but I wasn’t able to screen in to Norns while I was using fish shell in iTerm. Switching to Bash worked fine

#694

also— you can do the flashing process with a normal RPi if you have one around. or any linux computer.

i flash everything with an RPi and it’s weirdly faster than a macbook.

2 Likes
#695

Upgrading with the old image 90314 and a CM3+. Instructions from “full disk reset” works as expected, with some unusually side effects for hardware. Upgrading to latest tarball via serial works as expected. Process took about 2 hours from unscrewing the panel to getting the new Step startup sequencer to play sounds with all screws back in their place. I like the default pattern is a dorian mode this time :slight_smile:

weird stuff

Wifi is not enabled on boot. USB nubbin has blue light illuminated, menu says STATUS: unavailable. Connect and add menus are blank. Hostpot menu does nothing. After two reboots it fixes itself. Between reboots, crone crashed the first time and fixed itself the second.

kernel output

[  572.462586] dwc_otg_handle_wakeup_detected_intr lxstate = 2
[  573.012105] usb 1-1.1: new high-speed USB device number 6 using dwc_otg
[  573.143619] usb 1-1.1: New USB device found, idVendor=0bda, idProduct=8176
[  573.143627] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  573.143632] usb 1-1.1: Product: 802.11n WLAN Adapter
[  573.143636] usb 1-1.1: Manufacturer: Realtek
[  573.143640] usb 1-1.1: SerialNumber: 00e04c000001
[  573.291399] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready

Opening the system->wifi menu adds the following two lines

[  580.044122] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  580.181854] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
#696

Very excited for this release. Congratulations (and thank you) to everyone involved!

My Norns updated successfully (kinda), but now it’s only loading with an error message that reads, “NONE (error: AUDIO ENGINE)” on the main menu. When I attempt to select any script, it freezes on the “loading…” screen and I have to back out. Wifi and network connections are unavailable. I tried several resets and lit some candles and recited some incantations that I found on another forum. No dice.

As you can probably see, I’m not so good with this troubleshooting stuff. Anyone have any ideas? Please let me know if I should be posting this in the help thread instead.

1 Like
#697

You have a duplicate engine. Look into maiden while trying to load a script and you should easily be able to identify the culprit.

1 Like
#698

I’m still not able to connect to Maiden because Norns has connection issues. On the wifi page it says, STATUS: unavailable
NETWORK:
IP:

Both Network and IP are empty, and the Hotspot and Connect buttons below do nothing when I choose them.

#699

Sorry if this is banal, but does going near your WiFi router and pressing ADD display your home network?

#700

Nope, just says “none”.

To be clear, I’m using the newest 2.0 firmware, not the beta. Was never on the beta. Realized I should have posted this original issue in the regular Norns 2.0 release thread. I apologize for being too hyper with my hyperlinks.

#701

Sometimes it does that. Hard reset. Not software. As long as your WiFi login/pass was saved, it’ll immediately auto connect.

At least mine does. Good luck.

#702

I had to reboot twice for the wifi to work. It’s basically magic.

#703

Also try putting the WiFi nub into a different USB port. That happened to me a couple times when updating to the betas. If WiFi works after switching the port you’ll be able to switch it back to your preferred port

1 Like
#704

Additionally, light three candles and point the ports side of norns to the north.

14 Likes
#705

Thanks @trickyflemming Last night I got back home, updated both nornsies and redownloaded the scripts and they work! (and they’re awesome) :pray:

1 Like
#706

Three candles make a HOT SPOT. Folks!!

3 Likes
#707

Did you ever resolve this? Have the same issue when I updated.

#709

A post was merged into an existing topic: Orac, Sidekick, Pure Data and SC for Norns

#710

Four candles for eating :slight_smile:

#711