#336

Thanks for that, I was confused about what f, k and l functions, but now I’m not :slight_smile:

1 Like
#337

Probably a stupid question but I tried searching to no avail.

I’ve just got a Norns and I’m playing with Awake to start. I’m using a 1/4" set of headphones in the far left jack, but I only hear sequence one. I’ve programmed steps into both but I only hear the audio from the top sequence.

1 Like
#338

that is expected :slight_smile:
the bottom sequence just modifies the first, i.e. raises or lowers the note value of the top sequence.

edit: btw, welcome to Norns!

1 Like
#339

See? I knew it was a silly question. Many thanks, excited to get started.

2 Likes
#340

It’ll blow your mind. In fact this week I’m getting a second one :rainbow:

2 Likes
#341

While I’m at it, next question. On alphacactus’s glorb_wurm_brid, I’m occasionally getting some distorted glitches that sound like clipping, not the synth itself. Anyone else run into this?

#342

If you are running through a mixer, don’t make the mistake I made. Check to make sure your channel trim/gain levels are not too high. I set mine back to the defaults and norns is producing nothing but happy sounds now.

1 Like
#343

Thanks, right now I’m just running direct out to headphones from the headphone out on Norns

1 Like
#344

Test with/without reverb. Reverb adds a lot of drain on things. Could be a cause.

1 Like
#345

Thanks, just powered cycled Norns and that seems to make it happy. Yeah, reverb adds a lot of noise, I probably won’t use it much once I’m using Norns with the rest of my gear but its a nice-to-have when playing it standalone.

3 Likes
#346

With the next firmware you’ll be able to use 15sec reverb with no impact on the processor. I love it :slight_smile:

9 Likes
#347

Hey
has someone tried to connect a arturia beatstep pro to norns?
I was using the hello_gong script and wanted to control some parameters via Midi cc. Since there some settings for midi cc, I thought this could work.
But i did not manage to get it right. I set the timre cc for example to 10. when i look on my devices control center cc #10 would be the knob number 1.
So … it did not work…
does someone have a tip for me?

#348

Have you tried using midi learn?
From the parameters page press button 1 to access the load/save/assign cc page, put cc assign to on, then scroll to the parameter you want to assign and press button 3 and move the knob on the controller, and it gets assigned automatically.

3 Likes
#349

Thanks for the answer.
it did not work over the USB out of the Beatstep.
Finally I used the Midi Out with an adapter to USB and this worked.

thanks for the help

2 Likes
#350

possible known issue when device has multiple ports

would be helpful to confirm beatstep pro port complement

#351

@Justmat is it possible to increase the sample time in strides?

#352

Not directly from the strides code. Strides uses the Ack sampling engine, coded by @jah, and I am pretty sure those types of changes would need to be made there. What are you hoping to accomplish? There are a few other sample based engines that might better suited your needs :slight_smile:

#353

Has anyone got a version of Glut updated for 2.0? I’m getting a metro related error when trying to run the version from master

#354

Was attempting this yesterday, I think the issue lies with ‘gridbuf.lua’. Maybe @artfwo could help out.

#355

I just gave it a look and it looks like the grid refresh rate is too high (or it is for my DIY grid and it was throwing libmonome errors).

Along with updating to 2.0 syntax, I changed line 287 to 20 fps and it seems to be working
metro_grid_refresh = metro.init(function(stage) grid_refresh() end, 1 / 20)

1 Like