SSSR Labs SM010 and Teletype

scanner_darkly · 2018-05-13T16:30:09.040Z

i don’t know if all units had the problems i ran into (or if the problems were fixed) - might be worth checking with sssr labs.

GoneCaving · 2018-05-13T16:34:20.133Z

I did Both the >9.9V and the row 13 issues are present as a result of the switch chip used and cannot be fixed in software. They commented that attenuating the inputs (10V would be pretty hot even for eurorqck right?) and avoiding the other issue mean that the modules are still usable. I dunno, I’m still thinking about whether to proceed with buying one.

scanner_darkly · 2018-05-13T16:43:12.285Z

yeah, the 10V issue is probably not as critical but the row 13 issue means you can’t use that channel at all. if you’re planning to use it with teletype you could just program it in a way that would prevent row 13 from being connected to anything.

worth mentioning that i didn’t do any extensive testing of the module, so can’t confirm there are no other issues.

GoneCaving · 2018-05-13T16:48:53.577Z

Well if you make sure there’s awlays a signal into input 13 wouldn’t that solve the problem?

scanner_darkly · 2018-05-13T16:55:56.957Z

i checked my notes and yes, my records say if something is connected to input 13 it fixes the problem.

philmaguire · 2018-10-30T11:32:52.066Z

Were the hardware issues fixed? I’m quite tempted by the DIY kit.

pascalm · 2018-12-02T14:57:45.646Z

any news on this front?

scanner_darkly · 2018-12-02T18:09:48.051Z

have you tried contacting sssr labs?

j450n · 2019-01-26T20:15:25.665Z

Anyone know if this is fixed? I was interested in buying one when someone on the facebook quadraphonic discussion group pointed me over here to this thread. TIA.

scanner_darkly · 2019-01-26T20:25:52.720Z

since this is now getting linked from other places… could you post in that thread and suggest people should check with sssr labs, as only they can provide the answer?

j450n · 2019-01-26T21:12:47.112Z

Will do. Being newish, I follow blithely.

scanner_darkly · 2019-01-26T21:16:55.441Z

thanks! i posted my findings here back when i had the module, i don’t have the module anymore and i don’t have any new info. just want to make sure this thread is not used as the authoritative source of information.

Duksos · 2019-06-14T22:44:11.606Z

Hello
If possible can someone please guide me as to how to connect sssr sm010 with teletype and get it up and running
Thanks

scanner_darkly · 2019-06-15T05:47:28.256Z

SSSR Labs SM010 and Teletype Monome

he just posted a new 1.2 firmware on the web-site which includes i2c support. the teletype side of things is also done, i will post a beta later this week, just trying to finish a couple of things before i do. to connect use the connector marked CN1 REMOTE, the legend is below. please note SCL and SDA lines are swapped on SM010 compared to TT, make sure to connect everything correctly! (ground to ground, SCL to SCL and SDA to SDA). [image] list of ops: MA.SELECT 1..3 set current matrixarc…

Duksos · 2019-06-15T12:25:10.899Z

Yes I’ve read the thread before
Do you remember how to set the address on the sm010 side of things
I believe I have everything set except for that
And I cannot find anything in the sm010 manual
Thank you

scanner_darkly · 2019-06-15T17:21:08.108Z

found old notes - to select one of the 3 addresses go to setup, row 15 is where you select it (A/B/C). on teletype side you select it with MA.SELECT x where x is 1, 2 or 3. this is not stored in flash, you’ll need to put it in the init script if you’re not using the default address 1.

Duksos · 2019-06-18T01:21:37.387Z

Thank you i still got nothing tho
Does anyone remember if it Is still only 3 wires for I2c ?

scanner_darkly · 2019-06-18T16:43:55.039Z

twenty characters of yes

Duksos · 2019-06-22T10:41:12.478Z

Hello so sorry to bug again
Does anyone know how to hook this up with teletype?
I’m having an extra difficult time
I believe I have I2c connected properly
( 3 wires I swapped the sda and scl on sm010)
I went to line 15 on sm010 setup selected unit 1
I type in ma.select 1 on teletype
Next I try
Ma.step 1, the teletype responds with 1
What am I missing?
Thanks in advance if anyone can help

scanner_darkly · 2019-06-22T17:29:20.317Z

you don’t need a parameter with MA.STEP, it always advances by one step. have you tried other ops? double check i2c lines - GND to GND, SDA to SDA, SCL to SCL. do you have any other devices connected to i2c? do they work? finally, update sm firmware to the latest - 1.1 version doesn’t include teletype support.