State of the art SMD/DIY best practices

thom · 2017-10-09T15:29:23.863Z

These days I would probably buy easily available longer rails and cut them to size (to reduce costs).
Also a long time ago I bought irregular length rails from Erthenvar, but it’s more on the expensive side (in my experience).

Edit : I just realised you needed the rails three months ago…

Larrea · 2017-10-09T18:05:42.809Z

Thanks anyway!

I ordered a couple different batches from Erthenvar, for home brew racks/cases. Worked out nicely!

My favorite new configuration is 6U 42hp, as a kind of desktop sidecar.

Dewb · 2018-09-16T04:36:12.687Z

Folks who use the Sparkfun lead-free “best solder in the world”: Do you clean your PCBs after soldering to remove flux, and if so what’s your process? My old technique of IPA bath + toothbrush doesn’t work so well with the water-soluble flux, and the manufacturer recommendation for that flux appears to be water only.

http://documents.indium.com/qdynamo/download.php?docid=373

andrew · 2019-10-17T13:30:36.897Z

Approaching - DIY norns shield

While I don’t really do any DIY at the moment, I used to do a ton and am happy to offer tips on soldering etc in general and SMD specifically.
Maybe a separate build related thread or a more general DIY/soldering etc thread?

Approaching - DIY norns shield

would I be smarter to find another SMT project to start with or should I just dive in with some PCB backups if I’m excited about it (I am excited about it).

also any more tool req’s before I dive in

shooting the discussion over here - what should through-hole folks have / know before diving into a norns DIY or fates build ?

Dewb · 2019-10-17T14:35:53.097Z

Wayne and Layne have some SMT practice kits and a good series of overview & tutorial articles accompanying them:

https://www.wayneandlayne.com/smt/

I think the biggest thing is to get a pair of tweezers you feel really comfortable with. If you get that sorted, surface mount can be much faster and more pleasant than through-hole (no lead bending, board flipping, lead clipping, etc.)

Oootini · 2019-10-17T16:00:52.728Z

a decent iron, a steady hand, and good light

Ithacus · 2019-10-18T09:02:57.671Z

For 0805 components (caps/resistors etc), I find it helps to wet (solder) one of the pads first and then place the component with tweezers while re-flowing the solder. I found this much easier than just placing the part (and then soldering both pads), or using a flux pen (which can get messy) on simple 2 leg components.

Also, I found tweezers as shown below (with flattened ends) much easier to use than fine tipped versions:

image.png530×530 38.7 KB

Oh, and as @galapagoose says, use leaded solder (flows a lot nicer), and just breath out/blow while soldering

Oootini · 2019-10-18T11:56:34.878Z

Yes this is absolutely the approach I take. The last SMD board i built i solder blobbed a single pad of every resistor and cap position on the board before placing parts. Then, you just heat and move parts into place one by one, and then follow later with the other side of every part.

andrew · 2019-10-26T04:02:23.907Z

v in-depth and informative video. answered a lot of questions I was gonna post here

okyeron · 2019-10-26T04:29:43.769Z

Good stuff on that channel.

I think it’s hard to give advice since technique will/may depend on your own equipment, style, etc.

Like I use a very fine point tip on my iron so I can touch individual pins on a TSSOP, but others might prefer drag soldering instead.

I did just get wise to using a solder sucker to fix big solder blobs on ICs (instead of copper braid) I think that might’ve been in an adafruit video.

okyeron · 2019-10-26T04:34:26.027Z

Another tip

I like this no-clean liquid flux.

Then I have a small syringe with a fine flat tip and just suck up a milliliter or two at a time and squirt out a tiny bit where you need it.

andrew · 2019-10-26T04:47:16.313Z

o how much do I need to think about grounding ? I don’t have a strap :0

nurse_plissken · 2019-10-26T05:20:59.903Z

I’ve never bothered with it. I think it really will only be an issue with real sensitive electronics like fancy micro controllers and stuff, which I haven’t messed with very much. It won’t hurt to have a strap though!

I also do all my DIY work outside on the porch right now, so my practices are probably not state of the art

Cementimental · 2019-11-04T17:15:17.842Z

i remember seeing those in the maplin catalog 20+ years ago and haven’t thought about or used them since so you should be ok

andrew · 2019-11-06T21:10:41.004Z

anyone mind explaining testing strategies ?

I’ve got a multimeter and my first assembled board but honestly I don’t really know what to do with the two lol

just trying to make sure I didn’t make sure I didn’t make any soldering mistakes before I plug in my norns shield

barnaby · 2019-11-07T00:08:57.932Z

The first thing to do is always to test the resistance across the power supply to make sure there are no shorts. To do this, put the meter in resistance mode, connect the positive test lead to the positive power in, and the negative test lead to 0V (repeat across all combinations of pins on a multi-rail powered device, which I guess the norns shield is not). The resistance should start out very low but quickly rise to at least tens of thousands of ohms if not more as the decoupling capacitors charge up. If it stays at or close to 0 ohms, you have a short somewhere, which needs to be dealt with before you power up!

With access to the schematic you can do further testing without power, but typically if there are no power shorts it’s fine to plug in and see if the thing works. Test all buttons, LEDs and whatever, if some don’t work, check their connections, their multiplexing chip, etc.

okyeron · 2019-11-07T00:11:08.081Z

Try to find teat points where you can get known voltages. Usually this means looking at Eagle, isolating/viewing power /ground traces and then testing those points.

With those points you can check for continuity between power/ground - which would indicate a short somewhere.

Norns shield relies on pi for power so you gotta plug it all in to test voltages.

andrew · 2019-11-23T20:22:18.519Z

Approaching - DIY norns shield

IMG_3306961×870 290 KB

srry for the cross-post, but would anyone mind helping out with an IC diagnosis ? (codec is not registering) I hit those legs with my iron again post-photo and I can’t recognize any bridges - but I was having problems getting flux gunk clean so I suspect that could be an issue ? what are the tools and process for doing that properly ?

many thankssssssss

thopa · 2019-11-23T20:35:03.312Z

pin 13 maybe not making contact with the pad?

I know some people won’t agree but it all depends on how much you value your time, and how well you can deal with frustration and debugging, which is also a good thing because you learn a lot!

But if you want to make it as smooth as possible get a stereo microscope…they go around 250€ in amazon but will make your smd soldering so much easier and it actually it’s a lot of fun.

Lots of people do it with proper magnification.

Hope you get it fixed!

okyeron · 2019-11-23T21:31:34.483Z

@andrew - alternately - a cheaper USB microscope like one from Adafruit or this one from Amazon can get you closer to the action.

I use a photography loupe because I have it around from days past looking at film.

For the soldering - see if you can’t clean up the caps - some of those look pretty janky to me (although probably fine).

See about getting some no clean flux if you’re having issues with flux gunk.

For cleanup I use isopropyl alcohol and a toothbrush to do a quick scrub and then wipe the area with a microfiber cloth. Sometimes the cloth leaves behind fibers, but those are easy enough to get with a dry toothbrush.